Wooden bowl making tools

The advantage of the bowl sander is that the rotating head does not leave straight abrasive marks around the work like hand held sandpaper.

Works with 2" hook and loop sand paper disc. Just unscrew the shank, remove old pads, add all 10 new replacement pads to shank and tighten back down. Product Index. Customer Service. Catalog Index. Catalog Quick Order. Gift Certificate.

Band Saw Accessories. Dado Sets. Drill Press Accessories. Dust Collection. Dust Collectors. Forstner Bits. Glue Product.

Hand Tools. Miter Saw Accessories. Norton Waterstones. Pen Blanks. Pen Kits. Pocket Hole Jigs. Power Tools. Reciprocating Blades. Router Accessories. Router Bits.

Scroll Saw Accessories. Shop Accessories. Shop Safety. Table Saw Accessories. Make a V-groove by facing the flute, or red line, away from you, keeping the handle horizontal, and pushing into the wood. This means you are cutting into side grain when making heavy cuts and pushing the piece back into the chuck, which does not put much stress on the tenon, leading to less vibration.

Rotate the tool towards you, opening up the flute, but stop just before the red is visible from above. Pull the handle towards your body, while pushing the tool firmly onto the tool rest with your left hand.

Repeat this process, working in steps, from the center out towards the rim. Position the tool rest so it angles into the bowl and then repeat the process, which now becomes easier, as the steps are already in place to start the next series of cuts. These cuts are very fine, resulting in no tearout when done correctly. However, this small-diameter tool is prone to vibration if the tool rest is not kept close and will not reach the bottom of the bowl successfully.

This is where my degree bottom bowl gouge comes into play. The handle of this tool is kept in a horizontal position as my left hand pushes the tool down on the tool rest. Make several light passes, and each time bring the handle close to your side for stability as the cut nears the bottom. With experience, all of this can be done successfully without using a scraper, but making light passes with a scraper will also result in a satisfactory finish.

Let the wood come to the scraper, rather than forcing the tool into the wood. Frequent visits to your sharpening system will give the best results. All that remains is to remove the tenon and shape the base. I usually use a vacuum chuck in production, but this can be expensive for a new woodturner.

Most chuck manufacturers produce a bowl-reversing plate that will hold the bowl while you shape the base. The speed of the lathe needs to be reduced to about rpm. With a series of successful educational DVDs and a signature tool range, he teaches technique from his woodturning school in Ireland and around the world at symposia and events. For more, visit glennlucaswoodturning. The AAW and its journal, American Woodturner, are the foremost advocates for woodturning in the world. AAW members include professional woodturners and wood workers, amateurs, gallery owners, artists and collectors, and wood and tool suppliers.

Posted in: Woodturning. Turn on the lathe at a low speed and begin rounding the blank using a roughing gouge until the blank is smoothly and consistently rounded to the desired diameter. Next, remove the tailstock and re-position the tool rest so that it is parallel to the face of the blank that was previously connected to the tailstock.

Turn on the lathe slowly and begin turning the outer face of the bowl using a rounding gouge or a bowl gouge. Continue turning until the outer shape of the bowl is complete. Then, you'll need to cut a recess into the bottom of the bowl to accommodate the bowl chuck that came with your lathe.

Check the instructions on your bowl chuck to determine how deep and at what diameter to cut the recess. Once you are confident that you've cut the recess properly, remove the blank from the headstock, attach the bowl chuck to the blank and install it into the headstock. Rotate the blank by hand to make sure that it is spinning freely. To hollow out the bowl, position the tool rest parallel to the face of the blank and turn on the lathe so that the blank is rotating slowly.

Use two hands on a bowl gouge and gradually begin making light cuts to start hollowing out the center of the bowl. Make very gradual cuts to remove the center material, focusing on developing an inner shape to the bowl that matches the outer shape of the bowl until you have the desired, consistent thickness of wood between the inner and outer shapes.

Finally, use your bowl gouge or a scraper to create a consistent lip of the bowl, whether that be a rounded shape transitioning from the inner to the outer portions of the bowl, or more of a squared-off shape. And to think, this was just the practice piece! I am going to love decorating this for the different seasons. For the meantime, I just added some moss balls in it but even that looks lovely.

Wonderful mentioned earlier is going to be a bigger, deeper dough bowl to put on the dining room table. I may finish it differently because I want the finish to look more like an antique. Does anyone have any suggestions for that? Although that may be a while, I suppose I need to give Mr. W a little break. I will be sharing all of our work in there with you soon.

Good job! Kimberly you need to keep requesting items to be made! Lol…thanks Donna! Oh, I already have a long wish list, luckily Mr. W is very accomodating. Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. Notify me of follow-up comments by email. Notify me of new posts by email. This site uses Akismet to reduce spam. Learn how your comment data is processed.

I am so glad you came to visit my site today. I hope you can take something from here to inspire you or just make you smile. All material and images on this site are copyright of A Wonderful Thought, unless otherwise noted. If you would like to feature a project shown on this blog, you may use a maximum of ONE image provided credit is given to A Wonderful Thought and you include a visible link back to the the original post.

See my whole copyright policy here. Get More Updates! Oh My Gosh! This is so great! This is an awesome project and you are so creative!!!